Ai Bende ultra-low temperature refrigerator maintenance:
Ultra-low temperature refrigerator equipment is scarce due to refrigerant quality, expensive, complicated equipment structure and high maintenance cost. Ultra-low temperature refrigerators are often damaged, mostly due to improper use and maintenance. In the summer, the equipment is in a high-risk period. In order to ensure the normal operation of the ultra-low temperature refrigerator and prevent equipment damage, it is recommended to pay attention to the following points:
1. Ensure the ambient temperature. The working temperature of the ultra-low temperature refrigerator must be below 30 °C and the surrounding area is well ventilated. Excessive temperature or poor ventilation can cause damage to the equipment due to overload operation.
2. Regularly clean the heat filter (once every two months). The filter is not cleaned for a long time, and the dust blocks the mesh, resulting in poor heat dissipation, resulting in damage to the heat-dissipating motor and damage to the compressor. Please check the instruction manual for the cleaning method.
3. Regularly clean the ice at the door seal of the refrigerator. The door seal is not strict, and the heat preservation effect is seriously degraded, which may cause damage to the compressor due to long-term overload operation.
Ultra-low temperature refrigerator warranty knowledge:
The maintenance and maintenance of ultra-low temperature refrigerators is especially important for prolonging their life and normal use. If the temperature control is inaccurate, the objects to be preserved are often damaged, which has a great impact on the experimental results, thus affecting the normal work of the research.
1. Clean once a month to ensure cleanliness. Use a dry cloth to remove a small amount of dust from the inside and outside of the refrigerator. If the refrigerator is too dirty, use a neutral detergent. Rinse thoroughly with pure water. However, do not flush the water inside and outside the refrigerator, otherwise it will damage the insulation and cause malfunction. Lubricants are not required for compressors and other mechanical parts. Be careful when cleaning the fan at the rear of the compressor. After cleaning, perform a safety check to ensure that the plug of the refrigerator is plugged in, not to be connected; ensure that the plug is not abnormally hot; ensure that the power and distribution wires on the back of the refrigerator are not cracked or scored.
2. The alarm starts the alarm. When the alarm is activated, it can usually be checked by the following aspects.
**, check if there is a problem with the power supply or if the plug is pulled out of the socket;
Second, check whether the internal thermometer is beyond the appropriate range. In this case, placing the item will warm the refrigerator and trigger the alarm;
Third, check if there are too many items placed at one time.
3. Insufficient cooling of the refrigerator:
Check if there is frost on the surface of the evaporator; if the refrigerator door is over-switched; if the back of the refrigerator touches the wall; if too many items are placed.
4. The refrigerator is too noisy:
Check if the bottom plate is strong; if the refrigerator is stable; if it is unstable, adjust the movable screws so that the four corners are firmly supported on the bottom plate; if any objects touch the back of the refrigerator.
If the cooling effect is poor, the refrigerator does not stop, the heat pipe is not hot, and the evaporator has a small airflow sound. These are caused by the serious leakage of the refrigerant due to slow leakage. In the actual use process, there will be many other problems. The solution to such problems requires continuous accumulation of experience to eliminate obstacles, so that the ultra-low temperature refrigerator can achieve a good working condition.
The image measuring instrument is based on CCD digital image, relying on the powerful software capabilities of computer screen measurement technology and spatial geometry operation. After installing the special control and graphic measurement software, the computer becomes the measurement brain with the soul of the software and is the main body of the whole equipment. It can quickly read the displacement value of the optical ruler, and obtain the desired result instantly through the software module operation based on the spatial geometry; A graph is generated on the screen for the operator to compare the image with the image, so that the possible deviation of the measurement results can be identified intuitively.
Image measuring instrument is a high-precision optical image measuring instrument composed of high-resolution CCD color lens, continuous zoom objective, color display, video crosshair display, precision grating ruler, multi-function data processor, data measuring software and high-precision workbench structure.
The instrument is applicable to all application fields for the purpose of two-dimensional plane measurement. These fields include: machinery, electronics, molds, injection molding, hardware, rubber, low-voltage electrical appliances, magnetic materials, precision hardware, precision stamping, connectors, connectors, terminals, mobile phones, home appliances, computers (computers), liquid crystal television (LCD), printed circuit boards (circuit boards, PCBs), automobiles, medical devices, clocks, screws, springs, instruments, gears, cams, threads, radius templates, thread templates Wire and cable, cutter, bearing, screen, test screen, cement screen, screen plate (steel mesh, SMT template), etc.
Video Measuring Instrument,Video Measuring Machine,Cnc Video Measuring Machine,Image Measuring Instrument
Zhejiang dexun instrument technology co., ltd , https://www.dexunmeasuring.com